Samsung's original Galaxy Watch has been dead software walking for years. Now it has a second life running Google's operating system.
A developer published Wear OS 3.5 for the Galaxy Watch SM-R800 this weekend, and it is not a theme or a launcher pretending to be Wear OS. Tizen is gone. The watch boots Android 11 from the original Pixel Watch system image, running on a custom Linux 4.19 kernel, with Samsung's own bootloader left in place.
The repository went up on November 20 and it is already the most active thing on XDA's Wear OS development board, with new replies landing every few minutes.
What actually works
The surprising part is how long the list is. Straight from the project's own documentation:
- Display, touch, both buttons and the rotating bezel
- Always-on display
- Wi-Fi and Bluetooth, using the watch's own factory addresses
- Pairing through the Wear OS app, with internet passed through the phone
- Play Store, Google apps and notifications
- Gemini, by saying "Hey Google" or double-pressing the bottom button
- Speaker and microphone
- Heart rate, steps, accelerometer, gyroscope, barometer and light sensor
- GPS
- Wireless charging on Samsung's own charger
- Flashing updates over Wi-Fi
Deep sleep only partially works, and that is the one blunt caveat in the readme.
For a watch that Samsung shipped in 2018 with 4GB of storage and an Exynos 9110, getting Play Store, Gemini and a working rotating bezel out of it is a better outcome than most people expected. The bezel is the detail that matters most to Galaxy Watch owners. It is the reason people kept these watches, and it survives the port.
The catch list is short but serious
This is a one-watch project. The developer says it was developed and tested on a single device, and it supports only the 46mm Bluetooth SM-R800. Not the 42mm version, not the LTE models.
Installing it replaces Tizen entirely. You need a PC with Wi-Fi and Python 3, you put the watch into Download Wireless mode, and you flash a package over the air from the PC. The readme is explicit that nobody has tested the install on a watch still carrying Samsung's retail bootloader, and that flashing the build onto a different Galaxy Watch model can brick it.
Going back is possible. Flashing Samsung's stock firmware with Odin returns the watch to Tizen, and the project leaves the watch's factory data alone, which is where the Bluetooth and Wi-Fi addresses and the sensor calibration live. There is also one loud warning: never flash cm.bin from any firmware package, because it is tied to the watch's secure storage.
Early testers are already finding differences from the developer's own unit. In the community thread, one owner reported that Wi-Fi and Bluetooth kept disconnecting. Another said PIN and swipe pattern setup misbehaved, and that the upper button did nothing on their watch even though the documentation lists it as functional.
Why anyone would do this
Because Samsung stopped supporting the hardware. The Galaxy Store's Tizen watch service shut down on September 30, 2025, which cut off app downloads for the Gear line, the original Galaxy Watch, the Watch Active, the Watch Active 2 and the Watch 3.
Since then, owners who factory reset a Tizen watch have found basic pieces missing. We have seen reports of the Timer app vanishing after a reset, with no way to download it again because the store no longer serves those devices. A watch that still tells time but cannot install anything is not much of a smartwatch.
That is the gap this project fills. The port does not just modernize the watch, it restores access to a living app store. Google Play and the Wear OS app ecosystem are still being updated, while Tizen for watches is not.
The bigger question
Two obvious follow-ups are on everyone's mind in that thread: the Galaxy Watch Active 2 and the Galaxy Watch 3. The developer says there are currently no plans to support either, which makes sense given how much device-specific work went into this one.
Worth remembering that this is the same pattern we have watched play out on the Apple side, where a community project has been trying to make an Apple Watch work with Android. When a manufacturer walks away from hardware that still works, hobbyists fill the gap, and the results are usually impressive right up until they are not.
If you own an SM-R800 and you are comfortable with Odin, Download mode and the risk of a brick, the build is public and the instructions are detailed enough to follow. If you own any other Tizen Galaxy Watch, this is not for you yet.
Bottom line
This is the most interesting thing to happen to old Tizen watches since Samsung announced the shutdown. It is a genuine Wear OS port, not a skin, and it runs better than anyone had reason to expect on 2018 silicon.
It is also a single-developer project for a single model, tested on one watch, with disconnection reports already coming in. Treat it as a project for people who enjoy flashing watches, not as a fix you should recommend to your dad.
If you would rather stay on supported hardware, Samsung's current line is the safer path, and the Galaxy Watch 8 is the model most people should be looking at while the Ultra 2 covers the outdoor end. Our rundown of which Galaxy Watches are losing OS upgrades early is worth a read before you buy anything used.
Sources: galaxy-watch-wearos on GitHub, Gadgets and Wearables, Samsung Newsroom on the original Galaxy Watch, Android Authority on the Galaxy Store cutoff, How-To Geek on the Tizen shutdown.





